Bảng mã lỗi máy CNC Okuma và hướng dẫn cách sửa chữa

Bảng mã lỗi máy CNC Okuma – Xin chào các bạn! Khi Máy CNC Okuma của bạn gặp sự cố? Đang báo lỗi gì đó. Vui lòng gọi điện hoặc nhắn tin Zalo số 0915.283.693 “Nhớ chụp hình mã lỗi và gửi qua Zalo” để được hỗ trợ kỹ thuật nhanh chóng.

• Danh sách mã lỗi máy cnc okuma liệt kê dưới đây có trong các model hệ điều hành sau: OSP-P200L-20L, OSP-P300L, OSP-P300M, OSP-U10L, OSP-P20L, OSP-700L,…
• Xem thêm các dịch vụ hữu ích khác của chúng tôi tại đây: Sửa máy CNC Bình Dương – Sửa máy CNC Okuma

Danh sách Bảng mã lỗi máy CNC Okuma và Hướng dẫn sửa chữa

Cách tìm kiếm nhanh mã lỗi, bấm Ctrl + F nhập mã lỗi cần tìm rồi nhấn Enter↵

MCS là viết tắt của cụm từ “Montion Control System”

1. Bảng mã lỗi máy CNC Okuma – Alarm P List

• 0700 NC start-up error
• 0701 P100-Menu initialization failure
• 0702 Power failure upon start-up
• 0703 Load information file not found
• 0704 File load error
• 0705 Default scheduling table error
• 0706 Backup data file error
• 0707 DTL link/unlink error
• 0708 RT thread stack overflow
• 0709 Hardware exception
• 0710 System call error
• 0711 AlarmService library error
• 0712 AlarmService internal error (exception)
• 0713 AlarmService error
• 0714 Blue screen
• Bảng mã lỗi máy CNC Okuma
• 0715 P100-Menu error
• 0716 Floating point exception
• 0717 PLC control error
• 0718 Real time thread time over
• 0719 HXCP thread error
• 0720 AlarmService internal error
• 0721 DeviceNet error
• 0723 DeviceNet I/O data link file read
• 0725 M code data file
• 0726 Safety speed data error
• 0727 MCS firmware doesn’t support POS2 unit
• 0728 FL-net error
• 0729 Non-responsive software detected.
• 0731 R Spec. error
• 0732 Unable to execute lost motion compensation
• 0735 MCS DD encoder link error
• 0736 MCS DD encoder error
• 0737 MCS DD encoder (slave sensor) detected error
• 0738 MCS DD encoder initialization failure
• 0739 MCS DD encoder (slave sensor) initialization failure
• 0741 MCS firmware version error
• 0742 Relocation detection error
• 0744 MCS power supply unit overload
• Bảng mã lỗi máy CNC Okuma
• 0750 The spec.-code or select-soft. was wrong
• 0752 VDU communication error
• 0753 VDU detected error
• 0754 VDU initialization failure
• 0755 SIO link error
• 0756 PSC optical scale encoder error
• 0757 MF-SAFETY Error
• 0758 Safety I/O Error
• 0759 Safety Servo Link Error
• 0782 Magnetic encoder speed detection error
• 0783 MCS Rotary encoder 5 initialization failure
• 0784 MCS Rotary encoder 5 error
• 0785 MCS Rotary encoder 4 initialization failure
• 0786 MCS Rotary encoder 4 error
• 0787 MCS Rotary encoder 3 initialization failure
• 0788 MCS Rotary encoder 3 error
• 0789 MCS Rotary encoder 2 error
• 0790 MCS Rotary encoder 1 initialization failure
• 0791 MCS Rotary encoder 1 error
• 0792 MCS Linear scale 4 initialization failure
• 0793 MCS Linear scale 4 error
• 0794 MCS Linear scale 3 initialization failure
• 0795 MCS Linear scale 3 error
• 0796 MCS Linear scale 2 initialization failure
• 0797 MCS Linear scale 2 error
• Bảng mã lỗi máy CNC Okuma
• 0798 MCS Linear scale 1 initialization failure
• 0799 MCS Linear scale 1 error
• 0800 Spindle D/A control data file read
• 0801 TCP/IP board detected error
• 0802 Load information file not found
• 0803 File load error
• 0804 MSB file mismatch
• 0805 MOP-Tool parameter PBU load
• 0806 MOP-Tool tool data PBU load
• 0807 ACP panel status receipt error
• 0808 Speed change ratio failure
• 0810 NC I/O data file read
• 0812 MCS initialization error
• 0813 MCS Communication error
• 0814 MCS data file corrupt
• 0815 PLC real-time task loop error
• 0816 PLC initialization error
• 0817 MCS error 
• 0818 ADP initialization failure
• 0820 Machine data file read
• 0821 Spindle gear ratio
• 0822 Wheel data file read
• 0823 AXIS CONSTRUCTION DATA setting error
• 0824 Unit connection mistake
• 0825 AXIS CONSTRUCTION name not set
• 0826 AXIS CONSTRUCTION DATA file read
• 0827 Control axis not found
• 0828 Wire feed axis No. error
• Bảng mã lỗi máy CNC Okuma
• 0833 MCS option program file not sent
• 0834 MCS servo data error
• 0835 MCS communication error
• 0836 Program request illegal
• 0837 Loader spec. code data error
• 0838 Loader backup data file read error
• 0839 Specification conditions failure
• 0840 SuperHi-NC specification mismatch
• 0841 FCP4 board detected error
• 0842 Safety monitor spec. error
• 0845 Specification code setting failure
• 0846 Thermal deviation comp. backup data file read
• 0847 DNC-DT preload task start error
• 0848 PSCB error
• 0849 Synchronous axis tandem control initialization failure
• 0850 MCS Undefined alarm number
• 0851 MCS Inverter unit fault
• 0852 Mistake in data from MCS to NC
• 0853 MCS CON APA deviation
• 0854 MCS Power supply unit error
• 0855 MCS Converter link error
• 0856 MCS DC-bus voltage alarm
• 0857 MCS Motor overcurrent
• Bảng mã lỗi máy CNC Okuma
• 0858 MCS Power unit overheat
• 0859 MCS Power unit overload
• 0860 MCS Supply voltage flutter
• 0861 MCS Inverter capacity differs from spec.
• 0862 MCS Winding change failure
• 0863 MCS Encoder link error
• 0864 MCS Encoder detected error
• 0865 MCS Encoder initialization failure
• 0866 MCS Encoder with shaft detected error
• 0867 MCS Encoder with shaft initialization failure
• 0868 MCS ABSO SCALE error
• 0869 MCS ABSO SCALE initialization failure
• 0870 MCS Magnetic encoder alarm
• 0871 MCS Resolver alarm
• 0872 MCS Pulse generator count over
• 0873 MCS Motor overheat
• 0874 MCS Servo link error
• 0875 MCS Servo link disconnection
• 0876 Mistake in data from NC to MCS
• 0877 MCS Servo data error
• 0878 MCS Illegal command
• 0879 MCS CON speed over
• 0880 MCS Speed command over
• 0881 MCS DIFF over
• 0882 MCS APA speed over
• 0883 MCS Full-closed APA error
• 0884 MCS Over speed
• 0885 MCS Speed deviation over
• 0886 MCS Collision detected
• 0887 MCS Urgent-stop time over
• 0888 MCS Belt is broken
• 0889 MCS Axis change control error
• 0890 MCS Independent encoder initialization failure
• 0891 MCS Calculated current position lies outside range
• 0892 MCS Motor overload
• Bảng mã lỗi máy CNC Okuma
• 0893 MCS Safety speed monitor E-Link error
• 0894 MCS ABSO SCALE sub-slider detected error
• 0895 MCS Tandem control communication error
• 0896 MCS Full abso scale link error
• 0897 MCS Full abso scale error
• 0898 MCS Full abso scale initialization failure
• 0899 MCS Axis stop signal error
• 0940 Time sharing task control
• 0941 Real-time task control
• 0942 Real-time task loop error
• 0943 Main processor name incorrect
• 0944 Slave processor name incorrect
• 0945 Memory board/battery life
• 0951 SMP error
• 0952 Not equipped with processor board
• 0954 Peripheral processor start
• 0955 Spec. code: data file
• 0956 Backup data file read
• 0957 Graphic backup data file read
• 0958 Pitch compensation data file read
• 0965 Configuration file format error
• 0971 Cache data: Initialization error
• 0988 Cache data: Operation error
• 0989 CPU information table data incorrect
• 0990 TASK generate error
• 0991 TASK information table data incorrect
• 0992 PLC backup data file read
• 0993 TCP/IP board illegal
• 0994 TCP/IP configuration file
• 0995 Machine axis data file
• 0996 PLC axis data file
• 0997 PLC monitor backup data file read
• 0998 PLC sequence program load
• 0999 Synchronous tap data file read

2. Bảng mã lỗi máy CNC Okuma – Alarm A List

• 1071 Memory board battery depleted. Replace quickly!
• 1089 PLC alarm No. illegal
• 1091 PLC alarm message file not found
• 1092 PLC backup data file write
• 1093 PLC backup data file not found
• Bảng mã lỗi máy CNC Okuma
• 1094 PLC back up data file read
• 1097 Safety speed monitor error
• 1098 MCS not responsive
• 1100 Parameters not set
• 1101 Blue screen
• 1102 P100-Menu error
• 1103 AlarmService internal error
• 1104 DeviceNet slave idle mode
• 1105 DTL error
• 1106 FL-net initialization error
• 1107 Major FL-net error
• 1108 Non-responsive software detected
• 1109 Error occurred during CAS
• 1110 PLC control error
• Bảng mã lỗi máy CNC Okuma
• 1111 Shutting down to avoid damage
• 1112 Non-functioning device detected
• 1113 MCS Parameter learning error
• 1114 MCS Inertia identification error
• 1120 Overload detected.
• 1121 PSC Optical scale encoder error
• 1122 Safety controller error
• 1123 Safety speed monitor error
• 1132 VDU communication error
• 1133 VDU detected error
• 1134 VDU initialization failure
• 1135 MCS DD encoder link error
• 1136 MCS DD encoder error
• 1137 MCS DD Encoder (slave sensor) error
• 1138 MCS DD encoder initialization failure
• 1139 MCS DD encoder (slave sensor) initialization failure
• 1144 MCS Power supply unit overload
• 1146 Tailstock torque over
• 1150 MCS Undefined alarm number
• 1151 MCS Inverter unit fault
• 1152 Mistake in data from MCS to NC
• 1153 MCS CON APA deviation
• 1154 MCS Power supply unit error
• 1155 MCS Converter link error
• 1156 MCS DC-bus voltage alarm
• 1157 MCS Motor overcurrent
• 1158 MCS Power unit overheat
• 1159 MCS Power unit overload
• 1160 MCS Supply voltage flutter
• 1161 MCS Inverter capacity differs from spec.
• 1162 MCS Winding change failure
• 1163 MCS Encoder link error
• 1164 MCS Encoder detected error
• 1165 MCS Encoder initialization failure
• 1166 MCS Encoder with shaft detected error
• 1167 MCS Encoder with shaft initialization failure
• 1168 MCS ABSO SCALE error
• 1169 MCS ABSO SCALE initialization failure
• 1170 MCS Magnetic encoder alarm
• Bảng mã lỗi máy CNC Okuma
• 1171 MCS Resolver alarm
• 1172 MCS Pulse generator count over
• 1173 MCS Motor overheat
• 1174 MCS Servo link error
• 1175 MCS Servo link disconnection
• 1176 Mistake in data from NC to MCS
• 1177 MCS Servo data error
• 1178 MCS Illegal command
• 1179 MCS CON speed over
• 1180 MCS Speed command over
• 1181 MCS DIFF over
• 1182 MCS APA speed over
• 1183 MCS Full-closed APA error
• 1184 MCS Over speed
• 1185 MCS Speed deviation over
• 1186 MCS Collision detected
• 1187 MCS Urgent-stop time over
• 1188 MCS Belt is broken
• 1189 MCS Axis change control error
• 1190 MCS Independent encoder initialization failure
• 1191 MCS Calculated current position lies outside range
• 1192 MCS Motor overload
• 1194 MCS ABSO SCALE sub-slider error
• 1195 MCS Tandem control communication error
• 1196 MCS Full abso scale link error
• 1197 MCS Full abso scale error
• 1198 MCS Full abso scale initialization failure
• 1199 MCS Axis stop signal error
• 1200 Stroke end over
• 1202 Plus variable limit over
• 1203 Minus variable limit over
• 1213 User reserve code
• 1215 S.M command asynchronous
• 1216 Synchronous P code error
• Bảng mã lỗi máy CNC Okuma
• 1217 Torque limiter
• 1218 Torque limiter cancel
• 1219 Torque limit over
• 1220 Torque skip condition not satisfied
• 1221 Duplicate M-code
• 1222 Interrupt return pointer mismatch
• 1223 Thread feed command error
• 1225 Contour generation calculation error
• 1228 Illegal spindle mode
• 1229 Max. spindle rotation count not specified
• 1238 Spindle moved to interference distance
• 1243 Turret rotation conditions
• 1245 Axis moved to tool interference area
• 1257 Axis moved to chuck barrier area
• 1258 Axis moved to tailstock barrier area
• 1259 Tow-along tailstock connecting
• 1260 Tow-along tailstock command not possible
• 1262 W-axis plus variable limit over
• 1263 W-axis minus variable limit over
• Bảng mã lỗi máy CNC Okuma
• 1265 Parts catcher interlock
• 1272 Load exceeds No.2 limit value
• 1273 Load monitor command already executed
• 1278 Laser measurement data NG
• 1279 IND. CMP. data verification failure
• 1280 HP9825A unable to receive
• 1281 Abnormal data from HP9825A
• 1282 Data error from HP9825A
• 1283 C-axis command not possible
• 1299 Axis moved to sub-spindle interference distance
• 1300 W-axis unable to move
• 1303 Pickoff index position
• 1306 Sensor touch G00
• 1307 No contact with sensor
• 1309 Sensor protect
• 1316 ATC manual operation mode impossible
• 1322 Y-axis parameter illegal
• 1323 Illegal YS-axis position
• 1328 Adaptive control communication error
• 1329 Shift amount error
• 1332 Spindle belt slip
• 1334 APA error
• 1336 Moved inside horizontal barrier area
• 1338 LOAD MONITOR W overload
• 1339 Spindle different from position when door open
• 1345 Unable to move to tool change position
• 1347 STM time over
• 1348 Cycle time over
• 1349 Contour generation impossible
• 1353 Measurement system error
• 1355 Tow-along steady rest connected
• 1356 Steady rest torque over
• 1357 Positioning uncertain
• 1367 NC tailstock position error
• 1376 Cutting error
• 1393 Tow-along steady rest interference position
• 1412 HOME POSITION movement interlock
• 1426 Moved inside barrier area
• 1431 Safety speed over
• 1432 Safety monitor error detection
• 1435 Turret interference
• 1436 Power ON APA deviation
• 1440 Steady rest-Tailstock interlock
• 1441 Safety speed clamp
• 1453 Heavy work data not found
• 1460 TEMP RISE LIMIT OVER
• 1463 Spindle moved inside transportation barrier
• 1465 Spindle low acceleration mode condition
• 1466 HOB cutting overload
• 1467 Position scale error XS-axis
• 1468 Servo amp error XS-axis
• 1469 APA speed XS-axis
• Bảng mã lỗi máy CNC Okuma
• 1470 APA range XS-axis
• 1471 CON speed XS-axis
• 1472 Stroke end over XS-axis
• 1473 Actual position initialization error XS-axis
• 1474 Learning control error XS AXIS
• 1475 CAM execution data not selected XS-axis
• 1476 Learning control command XS-axis
• 1477 Syncronous mode command
• 1478 Chuck coordinates mismatch
• 1479 PSCB command error
• 1480 DIFF over XS-axis
• 1481 Drift compensation value over
• 1482 PSCB Real-time task error
• 1483 PSCB INT task loop error
• 1484 PSCB EC task loop error
• 1485 PSCB Time sharing task error
• 1486 PSCB Exception error
• 1487 PSCB Memory test error
• 1488 PSCB Overheat
• Bảng mã lỗi máy CNC Okuma
• 1489 First time drift compensation value over
• 1490 Synchronous mode spindle speed command
• 1491 Heavy tooling data not found
• 1492 PSCB P.G. underpulse
• 1493 PSCB P.G. overpulse
• 1494 PSCB Minus stroke end over
• 1500 Workpiece rest interlock
• 1501 Workpiece rest torque over
• 1504 Alarm-A at other system
• 1507 Unable to enter C-axis sync. Mode
• 1509 A turret and B turret interference
• 1510 Unable to execute Hi-CUT Pro control
• 1511 SPM contour control not possible
• 1512 SPM contour control error
• 1513 Unable to clamp workpiece
• 1514 Clutch A slip over limit
• 1515 Mistake in X, Z commands
• 1516 NC tailstock slide resistance over
• 1517 Turret or tool not at index cut position
• 1519 Spindle phase over limit
• 1520 Synchronous error limit over
• Bảng mã lỗi máy CNC Okuma
• 1521 NC tailstock error
• 1522 Linear guide cover interference area
• 1523 Workpiece weight data file not found
• 1524 Feed speed over
• 1525 M-tool spindle speed over in Hob mode
• 1526 Turret index error position
• 1527 Unable to execute while mounting LBB
• 1528 The attachment status mismatch
• 1529 M axis belt slip
• 1530 Steady-rests interference position
• 1531 Tool posture fluctuation reduction error
• 1532 Turret interference distance intrusion
• 1682 Magnetic encoder speed detection error
• 1683 MCS Rotary encoder 5 initialization failure
• 1684 MCS Rotary encoder 5 error
• 1685 MCS Rotary encoder 4 initialization failure
• 1686 MCS Rotary encoder 4 error
• 1687 MCS Rotary encoder 3 initialization failure
• 1688 MCS Rotary encoder 3 error
• 1689 MCS Rotary encoder 2 error
• 1690 MCS Rotary encoder 1 initialization failure
• 1691 MCS Rotary encoder 1 error
• 1692 MCS Linear scale 4 initialization failure
• 1693 MCS Linear scale 4 error
• 1694 MCS Linear scale 3 initialization failure
• 1695 MCS Linear scale 3 error
• 1696 MCS Linear scale 2 initialization failure
• 1697 MCS Linear scale 2 error
• Bảng mã lỗi máy CNC Okuma
• 1698 MCS Linear scale 1 initialization failure
• 1699 MCS Linear scale 1 error
• 1700 Emergency stop
• 1701 EC overload
• 1702 BDU overload
• 1703 EC circuit breaker
• 1704 Transformer overheat
• 1705 Oil pressure low
• 1706 Alarm detected from externally connected device
• 1707 Stroke end over
• 1708 Canceling stroke end limit
• 1709 XA-axis overload
• 1710 XB-axis overload
• 1711 ZA-axis overload
• 1712 ZB-axis overload
• 1713 Spindle rotation interlock
• 1714 S.M command asynchronous
• 1715 Spindle revolution over
• 1716 M03/M04 change command failure
• 1717 Unable to use M40, M43, M44 commands
• 1718 Tow-along tailstock command error
• 1719 Gear command/position mismatch
• 1720 Gear command error
• 1721 Gear neutral
• 1722 M19 command issued when gear neutral
• 1723 Z-axis moved to spindle interference distance
• 1724 Spindle synchronization interlock
• 1725 Impossible command issued during spindle synchronization
• 1726 C-axis command not possible
• 1727 C-axis ON/OFF command not possible
• 1728 C-axis clamp/unclamp command not possible
• 1729 Unable to confirm C-axis advance
• 1730 Turret clamp/position check error
• 1731 Turret index control alarm
• 1732 Turret rotation interlock
• 1733 Tool number input error
• 1734 Pickoff chuck interlock
• 1735 Sub-spindle chuck pressure insufficient
• 1736 Pickoff index interlock
• 1737 Turret unclamp interlock
• 1738 Turret rotation impossible
• 1739 Chuck clamp pressure insufficient
• 1740 Chuck open/close interlock
• 1741 Chuck unclamp
• Bảng mã lỗi máy CNC Okuma
• 1742 Chuck interlock cancel interlock
• 1743 Index chuck interlock
• 1744 Air chuck pressure error
• 1745 Chucking miss
• 1746 Chuck missclamp
• 1747 No tailstock quill advance answer
• 1748 Tailstock quill advance over
• 1749 Tailstock quill command error
• 1750 Tailstock interference
• 1751 Tow-along tailstock ON/OFF interlock
• 1752 Tow-along tailstock clamp/unclamp error
• 1753 Parts catcher interlock
• 1754 Coupling device alarm
• 1755 Robot inside machine
• 1756 Loader inside machine
• 1757 Loader interlock
• 1758 Loader not at escape position
• 1759 Loader/robot not at escape position
• 1760 Revolution tool M13/M14 change not possible
• 1761 Revolution tool gear mismatch
• 1762 Revolution tool gear interlock
• 1763 Tool revolution interlock
• 1764 Tool rotating when T command issued
• 1765 Rotation tool index interlock
• 1766 Rotation tool over speed
• 1767 M-axis clutch connection error
• 1768 Sub-spindle rotation over
• 1769 Sub-spindle index interlock
• 1770 Door interlock
• 1771 Door open/close limit switch NG
• 1772 Door open/close condition
• 1773 Unable to restore axis position when door closed
• 1774 Sensor head advance/retract interlock
• 1775 Touch setter limit
• 1776 Sensor head not at retract position
• 1777 ATC change arm position error
• 1778 No dummy tool in ATC turret
• 1779 Manual tool change operation interlock
• 1780 ATC system mode interlock
• Bảng mã lỗi máy CNC Okuma
• 1781 Loader/robot interference
• 1782 Power sequence error
• 1783 Turret unclamp time over
• 1784 Turret clamp time over
• 1785 NC parameter data transfer error
• 1786 Coolant error
• 1787 Door open/close check NG
• 1788 Safety door open
• 1789 Steady rest interlock
• 1790 Bar feeder not ready
• 1791 Bar feeder advance/retract interlock
• 1792 Turret rotation interlock
• 1793 Side cover interlock
• 1794 Rear cover interlock
• 1795 Side cover open/close lmt switch NG
• 1796 Turret index clutch disconnect error
• 1797 Invalid mode switch
• 1798 Steady rest missclamp
• 1799 Sensor protection cover interlock
• 1800 Locking switch NG
• 1801 Bar feeder setting position mismatch
• 1802 Safety guard interlock
• 1803 Machine enabling button error
• 1804 Safety speed monitor output error
• 1805 Teaching panel enabling switch error
• 1806 ATC Logic data file error
• 1807 Shutter close not possible
• Bảng mã lỗi máy CNC Okuma
• 1808 Safety fence locking switch NG
• 1809 Manual command time over
• 1810 Safety guard interlock
• 1811 Loader axis unable to move
• 1812 Mist lubrication unit error
• 1813 2nd spindle condition satisfy
• 1814 W-axis movement interlock
• 1815 Face driver pressure insufficient
• 1816 Safety fence open
• 1817 Setup switch ON
• 1818 Hand slide interlock
• 1819 Hand turning interlock
• 1820 Turnover interlock
• 1821 Magazine door lock error
• 1822 Slide step interlock
• 1823 Vibration cutter faulty
• 1824 Oil cooler error
• 1825 Spindle cooling unit error
• 1826 Oil air lubrication illegal
• 1827 Setup switch ON
• 1828 Laser sensor interlock
• 1829 Sp. oil air lub. air pressure error
• 1830 SP. oil air lub. oil level error
• 1831 Sp. oil air lub. oil pressure error
• 1832 Unloader advance/retract interlock
• 1833 Tow-along steady rest unclamp interlock
• 1834 Door interlock
• 1835 Workpiece receiver interlock
• 1836 Interference area intrusion
• 1837 Worktable overload
• 1838 Workpiece stabilizer interlock
• 1839 Deburring tool interlock
• 1840 M code data file mismatch
• 1841 Swing interlock
• 1842 Wrist rotation interlock
• 1843 Workpiece rest interlock
• 1844 Workpiece pusher interlock
• 1845 Hand rotation interlock
• 1846 Chuck grip confirmation unit faulty
• 1847 Tailstock air miss detection input NG
• 1848 Chuck grip failure
• Bảng mã lỗi máy CNC Okuma
• 1849 Workpiece unloading unit interlock
• 1850 Robot/Loader emergency stop
• 1851 Air pressure insufficient
• 1852 NC alarm
• 1853 Oil pressure insufficient
• 1854 Error detected from externally connected device
• 1855 M code time over
• 1856 Circuit breaker tripped
• 1857 Intrusion interlock
• 1858 No hand open/close output
• 1859 Swing position no output
• 1860 Axis interlock
• 1861 Stroke end over
• 1862 Canceling stroke end limit
• 1863 Loader interference
• 1864 Z/C-axis not in rotation possible area
• 1865 Swing position indefinite
• 1866 No workpiece clamped on hand A
• 1867 No workpiece clamped on hand B
• 1868 Wrist broken
• 1869 Hand open/ close interlock
• 1870 Hand clamp confirmation
• 1871 Coupling device error
• 1872 Safety fence interlock
• 1873 Door interlock
• 1874 Interlock release NG
• 1875 Safety fence lock NG
• 1876 Swing interlock
• 1877 Robot/Loader power sequence error
• 1878 Machine start impossible
• 1879 Workpiece puller holder interlock
• 1880 Loader hand/machine interference
• 1881 Part turnover device R clamp empty
• 1882 Part turnover device L clamp empty
• 1883 Part turnover device R advanced too far
• 1884 Part turnover device L advanced too far
• 1885 Loader/part turnover device interference
• 1886 Wrist turning position indefinite
• 1887 Workpiece puller interlock
• 1888 Backup roller interlock
• 1889 Auto workpiece I/O unit FWD pressure low
• 1890 Coolant flow insufficient
• 1891 Unloader interference position
• 1892 Unloader interlock
• 1893 Running mode error
• 1894 Running mode error
• 1895 Fire alarm
• 1896 Air source pressure low
• 1897 Lower turret drive belt torn
• 1898 OP panel within interference range
• 1899 Safety fence open
• 1900 Plus variable limit over
• 1901 Minus variable limit over
• 1920 User reserve code
• 1922 Torque limit over
• 1924 Barrier intrusion
• 1927 M code time over
• 1928 Cycle time over
• 1938 Machine start impossible
• 1939 Hand open/close interlock
• 1940 Loader Z-axis stopper set
• 1941 Safety guard interlock
• 1942 Safety speed over
• 1943 Safety speed monitor error
• 1944 Safety monitor error detection
• 1945 Running mode error
• 1949 Alarm-A at other system
• 1950 Safety speed monitor error
• 1951 Safety controller error
• 8500 Cut off error
• 8501 ATC shutter not close
• 8502 Unable to G21
• 8503 Spindle internal centering unit interlock
• 8504 Tool change command
• 8505 Tow-along steady rest clamp/unclamp
• 8506 Combination chuck interlock
• 8507 Automatic lubrication system error
• 8508 Coolant filter
• 8509 Cutting feed interlock
• 8510 Oil unit error
• 8511 B-axis clamp/unclamp interlock
• 8512 Turret position uncertain
• 8513 Coolant interlock
• 8514 Work conveyor interlock
• 8515 Work ejector interlock
• 8516 Touch setter unlock time over
• 8517 Work hand interlock
• 8518 Bar Feeder illegal
• 8520 Stopper interlock
• 8521 Work measurement operation
• 8522 Locater oil pressure
• 8523 Locater condition
• 8524 Oil motor overload
• 8525 Coolant motor overload
• 8526 Spindle cooling motor overload
• 8527 Oil skimmer overload
• 8528 Magnet separator overload
• 8529 Tool monitoring unit error detection
• 8530 Laser sensor input data error
• 8531 Door open
• 8532 Polish Material unit interlock
• 8536 Operation ready OFF condition
• 8537 Magazine door Interlock
• 8538 ATC shutter barrier area
• 8539 Complete stop
• 8540 X-axis in interference range
• 8541 Spindle phase synchronization interlock
• 8542 Synchronizing spindle phase
• 8543 Measurement Unit error
• 8545 Illegal robot/loader request
• 8546 Rolling-head movement error
• 8547 Drive jig unit interlock
• 8548 ACC interlock
• 8549 ACC door interlock
• 8550 ACC manual operation mode impossible
• 8551 Semi-dry unit error
• 8552 Sub-chuck interlock
• 8553 ACC airblow interlock
• 8554 Spindle table rotation
• 8555 B-Axis movement
• 8556 No mount magazine
• 8557 Tool Breakage sensor error
• 8558 L-tool index command
• Bảng mã lỗi máy CNC Okuma
• 8559 Part turn device advanced too far
• 8560 Override switch failure
• 8561 Grinding whl spindle motor overload
• 8562 Whl spdl coolant pressure drop/loss
• 8563 Inverter failure
• 8564 Turret drive belt disconnection
• 8566 Tool clamp interlock
• 8567 Spindle cover open/close limit SW NG
• 8568 Insulation error
• 8569 Magazine turn interlock
• 8570 Magazine tool No.
• 8571 Irregular coolant level
• 8572 ATC step time over
• 8573 Spingdle vibration
• 8574 MCS operation ready off
• 8575 Grinding whl spindle unit
• 8576 Grinding whl spindle unit interlock
• 8577 Axis interlock
• 8578 Coupling device interlock
• 8579 Tailstock and turret interference
• 8580 Canceling interference detection
• 8581 Loader automatic operation
• 8582 Illegal workpiece pusher confirmation
• 8583 ATC change arm overload
• 8584 Tailstock high/low change interlock
• 8585 Coiling prevention equip. interlock
• 8586 Air picker broken
• 8587 AREA SENSOR interlock
• 8588 Coolant Flow
• 8589 Chip conveyor faulty
• 8590 Tailstock pedestal condition
• 8591 C-axis synchronous condition
• 8592 Synchronizing C-axis
• 8593 Chip crusher error
• 8594 Sensor overstroke
• 8595 Linear guide cover interference
• 8596 Safety plug interlock
• 8597 Shuttle device hand clamp empty
• 8598 Ceiling door interlock
• 8599 Illegal tool clamp unit
• 8600 Ceiling door open/close limit SW NG
• 8601 ATC tool change arm inverter failure
• 8602 Chip pan cover interlock
• 8603 C-axis clamp/unclamp condition
• 8604 Long tool change protection
• 8605 Drive belt disconnection
• 8606 APC door open/close limit NG
• 8607 XB cover interference
• 8608 Illegal touch setter unit
• 8609 Axis overheat
• 8610 Invalid spindle winding condition
• 8611 Winding change error
• 8612 APC interlock
• 8613 APC clamp/unclamp time over
• 8614 APC escape position
• 8615 ATC shutter not open
• 8616 Coolant level low
• 8617 Thru-the-tool coolant filter clogged
• 8618 M spindle overload
• 8619 Machine axis travel limit over
• 8620 PLC system data
• 8621 M spindle air curtain pressure low
• 8622 Hydraulic unit oil level low
• 8623 Mist air lubrication unit
• 8624 Axis interlock
• 8625 Tool revolution command
• 8626 Ceiling door guide interlock
• 8627 Long boring bar change protection
• 8628 Spindlehead lib oil level low
• 8629 Spindlehead lubricant pressure low
• 8630 Hydraulic pressure drop
• 8631 Invalid safety-monitor spec.
• 8632 UNUSABLE interrupt program
• 8633 AAC Operation mode impossible
• 8634 ATC shutter open/close condition
• 8635 Spindle actual position detection error
• 8636 RSS unit Battery error
• 8637 RSS unit Communication error
• 8638 Sub-spindle head clamp condition
• 8639 Tailstock control mode ON/OFF cond.
• 8640 Center partition interlock
• 8643 Unusable PLC spec. code
• 8644 Fire extinguish unit power OFF
• 8645 Fire extinguish unit error
• 8646 Fire ext. unit power OFF or error
• 8647 Hand open/close switch NG
• 8648 Tailstock tool mode mismatch
• 8649 Measurement sensor unit interlock
• 8680 Area sensor interlock

3. Bảng mã lỗi máy CNC Okuma – Alarm B List

• 2049 PLC axis stroke end over
• 2050 PLC axis command
• 2051 PLC axis continuous positioning over
• 2052 Blue screen
• 2053 P100-Menu error
• 2058 Error occurred while CAS work
• 2059 Non-functioning device detected
• 2060 Fan motor error on panel computer unit
• 2090 The remaining time after relocation has passed
• 2092 MCS Parameter learning error
• 2114 MCS Inertia identification error
• 2120 Overload detected.
• 2132 VDU communication error
• 2133 VDU detected error
• 2134 VDU initialization failure
• 2135 MCS DD encoder link error
• 2136 MCS DD Encoder error
• 2137 MCS DD Encoder (slave sensor) error
• 2138 MCS DD encoder initialization failure
• 2139 MCS DD encoder (slave sensor) initialization failure
• 2144 MCS Power supply unit overload
• 2150 MCS Undefined alarm number
• 2151 MCS Inverter unit fault
• 2152 Mistake in data from MCS to NC
• 2153 MCS CON APA deviation
• 2154 MCS Power supply unit error
• 2155 MCS Converter link error
• 2156 MCS DC-bus voltage alarm
• 2157 MCS Motor overcurrent
• 2158 MCS Power unit overheat
• 2159 MCS Power unit overload
• 2160 MCS Supply voltage flutter
• 2161 MCS Inverter capacity differs from spec.
• 2162 MCS Winding change failure
• 2163 MCS Encoder link error
• 2164 MCS Encoder detected error
• 2165 MCS Encoder initialization failure
• 2166 MCS Encoder with shaft detected error
• 2167 MCS Encoder with shaft initialization failure
• 2168 MCS ABSO SCALE error
• 2169 MCS ABSO SCALE initialization failure
• 2170 MCS Magnetic encoder alarm
• 2171 MCS Resolver alarm
• 2172 MCS Pulse generator count over
• 2173 MCS Motor overheat
• 2174 MCS Servo link error
• 2175 MCS Servo link disconnection
• 2176 Mistake in data from NC to MCS
• 2177 MCS Servo data error
• 2178 MCS Illegal command
• 2179 MCS CON speed over
• 2180 MCS Speed command over
• 2181 MCS DIFF over
• 2182 MCS APA speed over
• 2183 MCS Full-closed APA error
• 2184 MCS Over speed
• 2185 MCS Speed deviation over
• 2186 MCS Collision detected
• 2187 MCS Urgent-stop time over
• 2188 MCS Belt is broken
• 2189 MCS Axis change control error
• 2190 MCS Independent encoder initialization failure
• 2191 MCS Calculated current position lies outside range
• 2192 MCS Motor overload
• 2194 MCS ABSO SCALE sub-slider error
• 2195 MCS Tandem control communication error
• 2196 MCS Full abso scale link error
• 2197 MCS Full abso scale error
• 2198 MCS Full abso scale initialization failure
• 2199 MCS Axis stop signal error
• 2200 G-code error
• 2201 M-code error
• 2202 Common variable error
• 2203 System variable error
• 2204 Sequence name error
• 2205 Numeric data error
• 2206 Character use error
• 2207 Program name error
• 2208 Character string error
• 2209 Hexadecimal data error
• 2210 Spindle max revolution error
• 2212 G132/G133 command error
• 2213 Program factor over
• 2214 Subscript left side incorrect
• 2215 Local variable use over
• 2216 System variable setting data over
• 2217 Output variable setting data mistake
• 2218 UNUSABLE G-code
• 2219 UNUSABLE M-code
• 2220 Subscript left side illegal
• 2221 UNUSABLE output variable No
• 2222 UNUSABLE input variable No
• 2223 UNUSABLE turret direct code
• 2224 UNUSABLE contour generation command
• 2225 UNUSABLE Y-Z circle command
• 2226 UNUSABLE thread cutting command
• 2227 Mnemonic or local variable mistake
• 2228 VSET sequence left command mistake
• 2229 EXPRESSION right side
• 2230 EXPRESSION calculation error
• 2231 EXPRESSION syntax incorrect
• 2232 EXPRESSION subscript mistake
• 2233 EXPRESSION buffer over
• 2234 EXPRESSION local variable
• 2235 Equal does not exist
• 2236 Program end code not found
• 2237 BRANCH (IF,GOTO) sequence name
• 2238 BRANCH (IF,GOTO) condition
• 2239 Mistake in F command
• 2240 Mistake in F/E command
• 2241 Mistake in I command
• 2242 Mistake in J command
• 2243 Mistake in K command
• 2244 Mistake in L command
• 2245 Mistake in P command
• 2246 Mistake in S command
• 2247 No S command
• 2248 Mistake in T command
• 2249 Mistake in X command
• 2250 Mistake in X/Z command
• 2251 Mistake in Z command
• 2252 Mistake in arc command
• 2253 Mistake in angle command
• 2254 Mistake in thread cutting cycle command
• 2255 Mistake in arc radius command
• 2256 Mistake in D command
• 2257 Mistake in gauging cycle command
• 2258 Mistake in C command
• 2259 Mistake in SB command
• 2260 Mistake in QA command
• 2261 Mistake in X/Y command
• 2262 Mistake in incremental command
• 2263 Command required for X-, Y-axes
• 2264 Mistake in Y command
• 2265 Distance calculation over limit
• 2266 Mistake in R command
• 2267 Mistake in drilling cycle command
• 2268 Mistake in angle command
• 2269 Angle chamfering command error
• 2270 Mistake in CD command
• 2271 Mistake in CL command
• 2272 Mistake in TM command
• 2273 Mistake in W command
• 2274 Mistake in CB command
• 2275 Mistake in HP command
• 2276 Mistake in CC command
• 2277 Mistake in torque limit command
• 2278 SUB PROGRAM repetition
• 2279 SUB PROGRAM stack
• 2280 SUB PROGRAM program name
• 2281 SUB PROGRAM data print
• 2282 SCHEDULE PROGRAM ‘Q’
• 2283 SCHEDULE PROGRAM mnemonic code
• 2284 SCHEDULE PROGRAM program end
• 2285 SCHEDULE PROGRAM main program load
• 2286 Plus variable limit over
• 2287 Minus variable limit over
• 2288 User reserve code
• 2289 Unable to write backup data file
• 2290 Program name not selected
• 2291 Main sequence error
• 2292 Restart failure
• 2293 MDI special G-code
• 2294 Special G-code table
• 2295 STM time over
• 2296 UGC No program end code
• 2297 UGC DELETE syntax
• 2298 UGC DEF syntax
• 2299 UGC TIP syntax
• 2300 UGC TIF syntax
• 2301 UGC No shape entry
• 2302 UGC Illegal numerical data
• 2303 UGC Illegal character
• 2304 UGC User variable
• 2305 UGC System variable
• 2306 UGC Illegal command
• 2307 UGC Program factor over
• 2308 UGC Coordinate data
• 2309 UGC END syntax
• 2310 UGC Command over
• 2311 UGC Command format
• 2312 UGC Additional parameter
• 2313 UGC Expression
• 2314 UGC Figure entry area over
• Bảng mã lỗi máy CNC Okuma
• 2315 UGC Unable to delete
• 2316 READ/WRITE No spec
• 2317 READ/WRITE Buffer over
• 2318 READ/WRITE Device No.
• 2319 READ/WRITE Data
• 2320 READ communication error
• 2321 WRITE communication error
• 2322 GET/PUT No spec.
• 2323 GET/PUT Buffer over
• 2324 GET/PUT Number of digits
• 2325 GET/PUT Variable designation
• 2326 GET Numerical data
• 2327 Calculation function no spec.
• 2328 Sub-program no spec.
• 2329 Sub-spindle interference distance
• 2330 Input/output variable no spec.
• 2331 Multiple machining no spec.
• 2332 Sub-spindle no spec.
• 2334 In-process gauging no spec.
• 2335 Post-process gauging no spec.
• 2336 Animation no spec.
• 2337 Graphic backup data file write failure
• 2338 Spindle orientation no spec.
• 2339 Load monitor no spec.
• 2340 Thread phase matching no spec.
• 2341 Circular thread cutting no spec.
• 2342 Circular thread cutting command
• 2343 Tool retract no spec.
• 2344 Tool retract interrupt enable com.
• 2345 Tool retract interrupt disable com.
• 2346 Tool retract interrupt return com.
• 2347 ROBOT no spec.
• 2348 ROBOT program name
• 2349 LOADER no spec.
• 2350 LOADER program name
• 2351 Coupling device program select no spec.
• 2353 CHAMFERING G01 mode
• 2354 CHAMFERING L over
• 2355 CHAMFERING L illegal order
• 2356 CHAMFERING X, Z illegal order
• 2357 CHAMFERING Any angle calculation
• 2358 CHAMFERING Any angle
• 2359 NOSE-R COMP. No spec.
• 2360 NOSE-R COMP. NOSE-R > circle-R
• 2361 NOSE-R COMP. Calculation
• 2362 NOSE-R COMP. Cancel G00 G01
• 2363 NOSE-R COMP. No cross point
• 2364 NOSE-R COMP. Entrance command error
• 2365 NOSE-R COMP. Thread cutting cycle
• 2366 TOOL RADIUS COMP. No spec.
• 2367 TOOL RADIUS COMP. NOSE-R comp. surface change
• 2368 TOOL RADIUS COMP. C-axis separation
• 2369 TOOL RADIUS COMP. QA command
• 2370 TOW-ALONG TAILSTOCK MOVEMENT no spec.
• 2371 TOW-ALONG TAILSTOCK MOVEMENT condition
• 2372 LASER MEASUREMENT no spec.
• 2373 LASER MEASUREMENT condition
• 2374 LAP No spec.
• 2375 LAP B illegal order
• 2376 LAP D illegal order
• 2377 LAP DA(DB) illegal order
• 2378 LAP H illegal order
• 2379 LAP H-U(W) < D (M73)
• 2380 LAP U(W) illegal order
• 2381 LAP U(W) > H
• 2382 LAP XA(ZA), XB(ZB) illegal order
• 2383 LAP Calculation error
• 2384 LAP Down step number over
• 2385 LAP Entry in LAP
• 2386 LAP Sequence name
• 2387 Unable to LAP Control
• 2388 LAP No G-code
• 2389 LAP NOSE-R comp. cancel
• 2390 LAP Entry in NOSE-R comp.
• 2391 LAP Shape designation
• 2392 MULTI CYCLE B illegal order
• 2393 MULTI CYCLE D illegal order
• 2394 MULTI CYCLE F illegal order
• 2395 MULTI CYCLE H illegal order
• 2396 MULTI CYCLE H-U(W) < D (M73)
• 2397 MULTI CYCLE I,K over
• 2398 MULTI CYCLE I,K illegal order
• 2399 MULTI CYCLE L illegal order
• 2400 MULTI CYCLE Entry in LAP
• 2401 MULTI CYCLE U(W) illegal order
• 2402 MULTI CYCLE U(W) > H
• 2403 MULTI CYCLE X,Z illegal order
• 2404 MULTI CYCLE Angle
• 2405 MULTI CYCLE Tool offset
• 2406 MULTI CYCLE Cycle start point
• 2407 MULTI CYCLE Entry in NOSE-R comp.
• 2408 MULTI CYCLE Width
• 2409 TOOL LIFE CONTROL no spec.
• 2410 Tool life management No spare tool
• 2411 TOOL LIFE CONTROL tool group
• 2412 TOOL LIFE CONTROL no T-entry
• 2413 TOOL LIFE CONTROL tool offset group
• 2414 TOOL LIFE CONTROL no T-offset
• 2415 MULTI-MACHINING CYCLE No spec.
• 2416 MULTI-MACHINING CYCLE C
• 2417 MULTI-MACHINING CYCLE I,K
• 2418 MULTI-MACHINING CYCLE Q
• 2419 MULTI-MACHINING CYCLE F
• 2420 MULTI-MACHINING CYCLE L
• 2421 MULTI-MACHINING CYCLE D
• 2422 MULTI-MACHINING CYCLE X,Z
• 2423 MULTI-MACHINING CYCLE SA
• 2424 MULTI-MACHINING CYCLE Feed G94
• 2425 MULTI-MACHINING CYCLE A
• 2426 MULTI-MACHINING CYCLE Thread cycle
• 2427 MULTI-MACHINING CYCLE U,W
• 2428 MULTI-MACHINING CYCLE SB
• 2429 MULTI-MACHINING CYCLE Y-axis mode
• 2430 ATC no spec.
• 2431 ATC syntax
• 2432 ATC TC
• 2434 ATC TL
• 2435 ATC MT
• 2436 ATC MG
• 2438 Unable to M06/M228 command
• 2440 Y-axis no spec.
• 2441 2 saddle machine no spec.
• 2444 Carrier axis variable limit over
• 2445 3-D coordinate conversion
• 2452 Chuck barrier area
• 2453 Tailstock barrier area
• Bảng mã lỗi máy CNC Okuma
• 2456 W-axis minus variable limit over
• 2457 X-axis correction stroke end over
• 2459 Restart axis position is illegal
• 2460 Change timing G13/G14
• 2462 Change timing G122/G123
• 2463 Change timing G140/G141/G142
• 2464 Spindle/turret G-code
• 2465 G122/G123 command mismatch
• 2466 Unable to issue M100 command during Nose-R comp.
• 2472 Y-axis control mode
• 2475 W-axis command G-code
• 2476 Mirror image coordinate selection
• 2477 Sub-spindle mode
• 2478 No workpiece coordinate mode command
• 2479 Contour generation calculation error
• 2480 G132/G133 command error
• 2486 NC turret no spec.
• 2487 Unable to select coordinates
• 2488 UNUSABLE X-axis command
• 2489 NC tailstock parameter error
• 2490 Chuck pressure out of range
• 2491 Horizon barrier intrusion
• 2492 Interrupt program: illegal command
• 2493 Linked external equipment program selection
• 2494 Chuck pressure command illegal
• 2495 Inverse time feed command format
• 2496 CAM data cannot be transmitted.
• 2497 T code
• 2498 Learning cannot be executed.
• 2499 Spindle marker latch data error
• 2500 MULTI-MACHINING CYCLE HS,HI,HJ,HK
• 2501 Recovering synchronous error
• 2502 Block Delete command error
• 2503 End sequence name error
• 2504 PREMIUM THREAD Command error
• 2505 CAM machine no spec.
• 2506 Tool center point control not possible
• 2507 CHP command error
• 2508 Machining mode command format
• 2509 MULTI-MACHINING CYCLE Return point
• 2510 Mistake in torque skip cycle command
• 2511 Remote buffer operation
• 2512 M-tool spindle overload
• 2513 Coordinate calculation
• 2514 MULTI CYCLE C-axis shift
• 2515 Remote buffer operation time out
• 2516 Remote buffer operation communication error
• 2517 W-axis control mode
• 2518 Synchronized tapping command
• 2519 Tailstock control command
• 2520 Mistake in TP command
• 2521 Mistake in BT command
• 2522 Mistake in BA command
• 2523 Thermistor error
• 2524 Mistake in AT command
• 2525 Chuck coordinate change condition
• 2528 Program selection unsuitable
• 2529 Thermal deviation compensation
• 2530 Machining process instruction no.
• 2531 Mirror turning mode
• 2532 System variable set condition error
• 2533 Steady rest over interference pos.
• 2534 LBB turret rotation impossible
• 2536 Coordinate movement rotation copy
• 2537 SLANT PROCESS MODE
• 2538 Incorrect system variable
• 2539 Mistake in B command
• 2541 PROGRAM PRINT command
• 2542 Feed axis retract function command
• 2543 Turret index error position
• 2544 TOOL-ID TOOL DATA
• 2545 MULTI-MACHINING CYCLE LD
• 2546 MULTI-MACHINING CYCLE LK
• 2547 No decimal point
• 2548 X-, Z-axis synchronized feed mode
• 2549 Tool no. mismatch after ATC sequence restart
• 2550 Home position no spec.
• 2551 External home position command
• 2552 Barrier area
• 2555 Linear guide cover interference area command
• 2557 Illegal steady rest command
• 2558 Turning position selection
• 2559 Attachment rotation not possible
• 2561 Illegal system command variable
• 2562 Tool posture fluctuation reduction
• 2563 Mistake in TE command
• 2564 Index disable position
• 2565 Load monitor system variable
• 2566 MULTI-MACHINING CYCLE No M-tool cycle command
• 2567 No helical cutting specifications
• 2568 Mistake in OF command
• 2569 Thermal deviation comp. backup failure
• 2570 W-axis position condition
• 2571 W-axis position no spec.
• 2572 Mistake in RC command
• 2573 Taper cutting cycle
• 2575 Mistake in ‘TD’,’TDG’,’OS’ commands
• 2576 Mistake in H command
• 2577 No axis movement command
• 2578 NO D COMMAND
• 2579 NO L COMMAND
• 2580 Mistake in XS command
• 2581 CAM data deployment mode
• 2582 CAM data file write protect
• 2583 Compensation value overflow
• 2584 CON speed XS-axis
• 2585 XS-axis command turret mode
• 2586 Synchronous mode execution impossible
• 2587 No A command
• 2588 Mistake in OF command
• 2589 Definition conditions
• 2590 Y-axis command
• 2591 Mistake in point command
• 2592 Transport barrier entry command
• 2593 Mistake in CF command
• 2594 Mistake in RJ command
• 2595 Synchronized rotation speed over
• 2596 Synchronized tap overload
• 2597 G15 command
• 2598 No Spec code. “Tool information management spec”
• 2599 Command not possible while mounting LBB.
• 2600 LAW-V machine no spec.
• 2601 Unable to issue T/TE command simultaneously
• 2602 SCHEDULE PROGRAM main program load
• 2603 Spindle rotation fluctuation control no spec.
• 2604 Tow-along steady rest no spec.
• 2605 Tow-along tailstock no spec.
• 2606 READ/WRITE file open
• 2607 Mistake in AP command
• 2608 Mistake in ON command
• 2609 A-axis control no spec.
• 2610 Zero offset select inpossible
• 2611 Spindle fluctuation control no spec.
• 2612 Mistake in TR command
• 2613 Mistake in MTM command
• 2614 Mistake in MTS command
• 2615 Mistake in MGS command
• 2616 B-axis mode
• 2617 Zero setting condition
• 2618 Workpiece detection sensor not ready
• 2619 Mistake in SW command
• 2622 Unset system variable read
• 2623 B-axis no spec.
• 2624 Tow-along steady rest type-B no spec
• 2625 Tow-along steady rest movement condition
• 2626 W-axis overlap
• 2628 Mistake in TW command
• 2629 Mistake in FW command
• 2630 Mistake in SC command
• 2631 DNC-DT Path name
• 2632 DNC-DT Program select
• 2633 DNC-DT Preload error
• 2634 DNC-DT Delete error
• 2635 Y-axis mode
• 2637 No axis movement command
• 2638 A/B saddle synchronized motion command
• 2639 Unable to issue C-axis command during helical cutting
• 2640 AC thread rotation count error
• 2641 AC thread fluctuation control not possible
• 2642 READ/WRITE No empty SAT
• 2643 READ/WRITE File open
• 2644 Unusable PRINT request
• 2645 YS-axis position
• Bảng mã lỗi máy CNC Okuma
• 2646 SYSTEM VARIABLE C-axis separation
• 2648 MG tool ready cycle no spec.
• 2649 SYSTEM VARIABLE Y-axis mode
• 2650 SYSTEM VARIABLE B-axis mode
• 2651 C-axis multi rotation mode
• 2652 Mistake in HA command
• 2653 Mistake in MN command
• 2654 Hob circular cutting command
• 2655 Hob cutting command
• 2657 SYSTEM VARIABLE C-axis connect
• 2658 B-axis independent encoder error
• 2659 NC tailstock position error
• 2662 NC TAILSTOCK no spec.
• 2663 Turning cut condition interlock
• 2667 X-axis mirror image coordinates selected
• 2668 X-axis mirror image coordinates impossible
• 2671 C-axis sync control no spec.
• 2672 C-axis sync command format
• 2674 Default status macro cannot be executed
• 2675 Tool posture command error
• 2676 Tool posture command angle conversion error
• 2677 Attachment change not possible
• 2678 SPM contour control not possible
• 2679 Mistake in Q command
• 2682 Magnetic encoder speed detection error
• 2683 MCS Rotary encoder 5 initialization failure
• 2684 MCS Rotary encoder 5 error
• 2685 MCS Rotary encoder 4 initialization failure
• 2686 MCS Rotary encoder 4 error
• 2687 MCS Rotary encoder 3 initialization failure
• 2688 MCS Rotary encoder 3 error
• 2689 MCS Rotary encoder 2 error
• 2690 MCS Rotary encoder 1 initialization failure
• 2691 MCS Rotary encoder 1 error
• 2692 MCS Linear scale 4 initialization failure
• 2693 MCS Linear scale 4 error
• 2694 MCS Linear scale 3 initialization failure
• 2695 MCS Linear scale 3 error
• 2696 MCS Linear scale 2 initialization failure
• 2697 MCS Linear scale 2 error
• 2698 MCS Linear scale 1 initialization failure
• 2699 MCS Linear scale 1 error
• 2700 No workpiece confirmation error
• 2701 Sequencer Error
• 2702 Spindle command during C-axis connection
• 2703 Chucking miss
• 2704 Chucking miss air off order impossible
• 2705 Tailstock quill over advance
• 2706 Polygon cutting command condition
• 2707 Invalid command during polygon cutting
• 2708 Invalid rotation tool gear
• 2709 Sub-spindle synchronization interlock
• 2710 Sub-spindle synchronization cutting
• 2711 Door open
• 2712 ATC no spec.
• 2713 Invalid ATC syntax
• 2714 Invalid ATC TC no.
• 2716 Invalid ATC TL no.
• 2717 Invalid ATC MT no.
• 2718 Invalid ATC MG no.
• 2719 Invalid ATC command
• 2720 M06/M228 interlock
• 2721 Turret number mismatch
• 2722 Robot/Loader request illegal
• 2723 ATC next tool preparation interlock
• 2724 Invalid ATC sub arm
• 2725 Invalid RS tool L/M
• 2726 Magazine encoder read
• 2727 Magazine rotation interlock
• 2728 Invalid magazine tool no.
• 2729 No magazine return pot
• 2730 Tool insertion interlock
• 2732 Tailstock sleeve position data error
• 2733 Coolant flow
• 2734 Coolant level
• 2735 Spindle low rotation command
• 2736 SVP time constant switching no spec.
• 2737 Invalid tailstock switch position
• 2738 Synchronous hobbing interlock
• 2739 Invalid synchronous hobbing mode
• 2740 Incorrect magazine tool data
• 2741 Touch setter unlock time over
• 2742 Setup switch ON
• 2743 Irregular coolant level
• 2744 Tool breakage
• 2745 Low high-pressure coolant pressure
• 2746 Hydraulic oil unit error
• 2747 Index disable position
• 2748 CPU fan stop
• 2749 Hydraulic oil level lower limit
• 2750 Tool monitoring unit error detection
• 2751 Coolant/Oil mist command
• 2752 Air pressure
• 2753 Unable to change tool
• 2754 Invalid coolant command
• 2755 Semi-dry unit error
• 2756 Actual tool data setting
• 2757 Oil mist unit error
• 2758 Invalid position data
• 2759 Coolant discharge error
• 2760 Sub-spindle rotation tool interlock
• 2761 W-axis overlap mode
• 2762 Chucking miss
• 2763 Coolant filter
• 2764 Coolant error
• 2765 Chip conveyer filter clogged
• 2766 Invalid M-tool spindle command
• 2767 M-spindle low rotation interlock
• 2768 Program check mode interlock
• 2769 Invalid spindle control command
• 2770 SVP time constant switching command
• 2771 APC clamp confirmation
• 2772 APC system mode
• 2773 APC M command
• 2774 Thread cutting cycle interlock
• 2775 Sensor head interlock
• 2776 M command not completed
• 2777 Cross rail positioning sensor error
• 2778 Cross rail motor overload
• 2779 Axis lube motor overload
• 2780 Axis lube pressure ON confirmation
• 2781 No AT command
• 2782 Axis lube pressure OFF confirmation
• 2783 Oil hole motor overload
• 2784 Invalid MT command
• 2785 Invalid AT command
• 2786 No S command
• 2787 No SB command
• 2788 Invalid SB command
• 2789 Coolant tank filter clogged
• 2790 Shower coolant motor overload
• 2791 M spindle head cooling unit
• 2792 Invalid RH command
• 2793 Incorrect attachment index position
• 2794 Mist air lube unit
• 2795 Warming up error
• 2796 Sequence restart
• 2797 Axis interlock release
• 2798 Invalid BC command
• 2800 Alarm detected from externally connected device
• 2801 Turret rotation interlock
• 2802 Invalid long boring bar command
• 2803 ATC tool data setting
• 2804 Attachment control
• 2805 Limit confirmation impossible
• 2806 Door interlock
• 2807 Invalid M code
• 2848 Chip conveyer overload
• 2849 Sensor unit in interference range
• 2850 External request interlock
• 2851 Machine change M-code
• 2852 Hand open/close interlock
• 2853 Teaching operation interlock
• 2854 Machine linked M-code
• 2855 Coolant filter
• 2856 Coolant motor overload
• 2857 UNUSABLE M-code
• 2858 Hand slide advance interlock
• 2887 Coupling device interlock
• 2888 Lube tank level
• 2890 Workpiece clamp miss
• 2891 Tailstock air miss
• 2892 Unable to execute air shut-off command
• 2893 Hydraulic oil controller faulty
• 2894 Spindle lubricant controller error
• 2895 Coolant controller error
• 2896 No touch setter
• 2897 Unloader no spec.
• 2898 Unloader interference position
• 2899 Gauge error
• 2900 DIRECTION V variable
• 2901 DIRECTION Check address
• 2902 DIRECTION Data operation
• 2903 DIRECTION Character use
• 2904 DIRECTION Numerical data
• 2905 DIRECTION Parameter/point
• 2906 DIRECTION Register
• 2907 DIRECTION F
• 2908 DIRECTION E
• 2909 DIRECTION Sequence no.
• 2910 UNUSABLE G-code
• 2911 UNUSABLE M-code
• 2912 UNUSABLE Address character
• 2913 UNUSABLE Mnemonic
• 2914 UNUSABLE Left side direction
• 2915 EXPRESSION Calculation
• 2916 EXPRESSION Syntax
• 2917 EXPRESSION Right side
• 2918 EXPRESSION Left side
• 2919 EXPRESSION Buffer over
• 2920 VARIABLE Buffer over
• 2921 PROGRAM DIRECT Program name
• 2922 PROGRAM DIRECT V variable
• 2923 PROGRAM DIRECT Character use
• 2924 PROGRAM DIRECT G-code
• 2925 BRANCH Sequence name
• 2926 BRANCH Condition
• 2927 Parameter setting illegal
• 2928 Parameter playback impossible
• 2929 Register setting impossible
• 2930 Program plus var. limit over
• 2931 Program minus var. limit over
• 2932 Program request illegal
• 2933 Program request impossible
• 2934 Program external request impossible
• 2935 No program selection
• 2936 No program
• 2937 Program end code
• 2938 Program analysis complete
• 2939 SUB PROGRAM stack
• 2940 SUB PROGRAM Program name
• 2941 SUB PROGRAM Buffer over
• 2942 Command impossible while running
• 2943 Data file read
• 2944 Comment end code not found
• 2945 Equal does not exist
• 2946 No spec.
• 2948 DIRECTION Y
• 2949 DIRECTION Z
• 2950 DIRECTION D
• 2951 DIRECTION L
• 2952 DIRECTION SU
• 2953 DIRECTION Torque limit
• 2954 PROGRAM DIRECT M-code
• 2955 PROGRAM DIRECT Equal
• 2956 Machine change M-code
• 2957 G22 feed
• 2958 Main sequence
• 2959 Barrier limit
• 2960 User reserve code
• 2961 Calculation function no spec.
• 2962 Subscript function no spec.
• 2964 NC program selection
• 2965 EXPRESSION subscript
• 2966 M code time over
• 2967 Cycle time over
• 2968 Program selection
• 2969 G23 FEED
• 2970 DIRECTION X
• 2971 DIRECTION I
• 2972 DIRECTION J
• 2973 DIRECTION K
• 2974 PROGRAM DIRECT hexadecimal data
• 2975 PROGRAM DIRECT character string
• 2976 Stopper position data illegal
• 2977 Program selection unsuitable
• 2978 DIRECTION V
• 2979 DIRECTION C
• 2980 No decimal point
• 2981 DIRECTION Q
• 2982 Time over

4. Bảng mã lỗi máy CNC Okuma – Alarm C List

• 3055 Device temperature too high
• 3056 Non-functioning device detected
• 3057 Unable to start during virus scan
• 3120 Overload detected.
• 3122 Maintenance (by user) necessary
• 3132 VDU communication error
• 3133 VDU detected error
• 3134 VDU initialization failure
• 3135 MCS DD encoder link error
• 3136 MCS DD Encoder error
• 3137 MCS DD Encoder (slave sensor) error
• 3138 MCS DD encoder initialization failure
• 3139 MCS DD encoder (slave sensor) initialization failure
• 3144 MCS Power supply unit overload
• 3150 MCS Undefined alarm number
• 3151 MCS Inverter unit fault
• 3152 Mistake in data from MCS to NC
• 3153 MCS CON APA deviation
• 3154 MCS Power supply unit error
• 3155 MCS Converter link error
• 3156 MCS DC-bus voltage alarm
• 3157 MCS Motor overcurrent
• 3158 MCS Power unit overheat
• 3159 MCS Power unit overload
• 3160 MCS Supply voltage flutter
• 3161 MCS Inverter capacity differs from spec.
• 3162 MCS Winding change failure
• 3163 MCS Encoder link error
• 3164 MCS Encoder detected error.
• 3165 MCS Encoder initialization failure
• 3166 MCS Encoder with shaft detected error
• 3167 MCS Encoder with shaft initialization failure
• 3168 MCS ABSO SCALE error
• 3169 MCS ABSO SCALE initialization failure
• 3170 MCS Magnetic encoder alarm
• 3171 MCS Resolver alarm
• 3172 MCS Pulse generator count over
• 3173 MCS Motor overheat
• 3174 MCS Servo link error
• 3175 MCS Servo link disconnection
• 3176 Mistake in data from NC to MCS
• 3177 MCS Servo data error
• 3178 MCS Illegal command
• 3179 MCS CON speed over
• 3180 MCS Speed command over
• 3181 MCS DIFF over
• 3182 MCS APA speed over
• 3183 MCS Full-closed APA error
• 3184 MCS Over speed
• 3185 MCS Speed deviation over
• 3186 MCS Collision detected
• 3187 MCS Urgent-stop time over
• 3188 MCS Belt is broken
• 3189 MCS Axis change control error
• 3190 MCS Independent encoder initialization failure
• 3191 MCS Calculated current position lies outside range
• 3192 MCS Motor overload
• 3194 MCS ABSO SCALE sub-slider detected error
• 3195 MCS Tandem control communication error
• 3196 MCS Full abso scale link error
• 3197 MCS Full abso scale error
• 3198 MCS Full abso scale initialization failure
• 3199 MCS Axis stop signal error
• 3202 User reserve code
• 3203 Warm up run
• 3204 Running time over
• 3205 Work counter over
• 3206 Cycle time over
• 3207 DNC Start conditions
• 3208 DNC Initialization sequence impossible
• 3209 DNC Illegal text from host
• 3210 DNC Incorrect machine No.
• 3211 DNC Text format error
• 3212 DNC Text receipt error
• 3213 DNC Text transmission error
• 3214 FMS Coupling mode change
• 3215 FMS HOST CPU alarm
• 3216 FMS Operation mode select
• 3217 DNC-B buffer operation
• 3218 DNC-B buffer operation change
• 3226 Common unit illegal
• 3231 Program select
• 3232 Load monitor overload
• 3238 ROBOT alarm/reset
• 3240 LOADER alarm/reset
• 3241 Post-process gauging Unable to transmit
• 3242 Post-process gauging Unable to receive
• 3243 Post-process gauging Time out
• 3244 Post-process gauging Data format error
• 3245 Gauging data out
• 3246 CEJ MATIC Data NG
• 3247 CEJ MATIC Data read
• 3248 Size catcher Data NG
• 3249 Size catcher Gauging error
• 3250 Size catcher Unable to transmit
• 3251 Size catcher Unable to receive
• 3252 Size catcher Time out
• 3253 Size catcher Data format error
• 3254 Schedule program start
• 3255 Main program start
• 3261 Tool life management No spare tool.
• 3264 RS-232C communication illegal
• 3266 Workpiece counter full count
• 3271 Gauging sensor battery change
• 3279 DNC Machining start conditions
• 3280 DNC Data receipt start conditions
• 3289 Load monitor low load
• 3295 Quality check alarm
• 3300 Tool data output
• 3314 External tool offset input
• 3316 Position encoder adjustment required.
• 3319 DNC Ethernet receipt command not allowed.
• 3320 DNC Ethernet receipt error
• 3321 DNC Ethernet transmission error
• 3331 NC tailstock position error
• 3332 Reboot machine.
• 3682 Magnetic encoder speed detection error
• 3683 MCS Rotary encoder 5 initialization failure
• 3684 MCS Rotary encoder 5 error
• 3685 MCS Rotary encoder 4 initialization failure
• 3686 MCS Rotary encoder 4 error
• 3687 MCS Rotary encoder 3 initialization failure
• 3688 MCS Rotary encoder 3 error
• 3689 MCS Rotary encoder 2 error
• 3690 MCS Rotary encoder 1 initialization failure
• 3691 MCS Rotary encoder 1 error
• 3692 MCS Linear scale 4 initialization failure
• 3693 MCS Linear scale 4 error
• 3694 MCS Linear scale 3 initialization failure
• 3695 MCS Linear scale 3 error
• 3696 MCS Linear scale 2 initialization failure
• 3697 MCS Linear scale 2 error
• 3698 MCS Linear scale 1 initialization failure
• 3699 MCS Linear scale 1 error
• 3700 Power save ON
• 3701 CPU temperature
• 3702 Warm up run
• 3703 Oil filter
• 3704 Lube tank flow
• 3705 Lube tank level
• 3706 Spindle lube pressure
• 3707 Spindle cooler error
• 3708 Oil cooler error
• 3709 Coolant level
• 3710 Air blow pressure
• 3711 Air pressure
• 3712 Program selection interlock
• 3713 Chip conveyer overload
• 3714 ZA-axis overload
• 3715 ZB-axis overload
• 3716 XA-axis overload
• 3717 XB-axis overload
• 3718 Coupling device error
• 3719 ROBOT control
• 3720 ROBOT alarm/reset
• 3721 ROBOT/LOADER control
• 3722 LOADER alarm/reset
• 3723 Schedule program start
• 3724 Main program start
• 3725 CEJ MATIC data NG
• 3726 CEJ MATIC data read
• 3727 Auto power off impossible
• 3728 Oil cooler level
• 3729 Coolant error
• 3730 Coolant flow
• 3731 Coolant abnormal
• 3732 Robot/loader axis safety speed over
• 3733 Robot/loader safety speed monitor error
• 3734 ATC step time over
• 3735 Next tool preparation impossible
• 3736 Coolant filter
• 3737 Mist collector
• 3738 Mode switch operation prohibited
• 3739 Control box air conditioner error
• 3740 Air filter clogged
• 3741 Index chuck oil level
• 3742 ATC-axis circuit breaker
• 3743 ATC-axis motor overload
• 3744 Chucking miss air
• 3745 Mist lubrication unit
• 3746 External start switch
• 3747 NC start button
• 3748 Door sensor
• 3749 Automatic lubrication system error
• 3750 Tailstock absolute encoder error
• 3751 Invalid external tool offset input
• 3752 Coolant supply
• 3753 Drain tank
• 3754 Mist collector
• 3755 Workpiece conveyor error
• 3756 Unmachined workpiece detection
• 3757 Bar feeder error
• 3758 Oil mist error
• 3759 Tool monitoring unit error detection
• 3760 Fan cooling unit pressure
• 3761 TOOL change not possible
• 3762 ACC step time over
• 3763 Switch disabled
• 3764 Oil controller unit
• 3765 Spindle vibration sensor
• 3766 Coupling device interlock
• 3767 Tailstock holding miss check air
• 3768 Irregular coolant level
• 3769 Side cover open
• 3770 Safety door open
• 3771 Lube tank motor run time over
• 3772 Coolant flow
• 3773 Earthquake detected
• 3774 EC circuit breaker
• 3775 Lubrication unit error
• 3777 Air blow flow
• 3778 M axis cooling fan overload
• 3779 APC system conditions
• 3780 Touch setter unit error
• 3781 EC overload
• 3782 Sensor contact signal error
• 3783 ATC interlock
• 3784 Fire extinguish unit power OFF
• 3785 Spindle lubrication unit
• 3786 Chip flush-out motor overload
• 3787 M-axis unit command mismatch
• 3788 AAC system condition
• 3789 Air dryer unit error
• 3790 Ext. program select parity check
• 3791 Mist air lubrication unit
• 3792 Chucking miss
• 3793 Coolant level low
• 3794 Power source unit overload
• 3795 Hydraulic oil unit
• 3796 RSS unit battery error
• 3797 RSS unit communication error
• 3798 Unloader interlock
• 3800 Transfer data error
• 3843 Safety fence open
• 3844 Invalid loader grease lubrication input
• 3845 Coolant level lower limit
• 3846 M/C panel at interfering position
• 3847 Invalid limit/proximity switch
• 3848 Anti-gouge unit faulty
• 3849 Tool counter full count
• 3850 External alarm
• 3851 Tool counter faulty
• 3852 Tail stock chuck position
• 3853 Invalid loader limit/proximity switch
• 3854 Chip conveyor stop
• 3855 Oil air unit oil level low
• 3856 Coolant motor overload
• 3857 Oil skimmer overload
• 3858 Chuck grip confirmation unit faulty
• 3859 Fire extinguisher error
• 3860 Fire extinguisher power OFF or error
• 3861 Chip conveyer filter clogged
• 3862 Filtration unit error
• 3874 Sub chip conveyor error
• 3875 Absolute encoder controller error
• 3876 Workpiece loading unit stop signal ON
• 3877 Workpiece counter full count
• 3878 Concentrated chip conveyor
• 3879 Gauging NG
• 3880 Spindle air purge pressure
• 3881 Turnover cycle time over
• 3882 Start impossible
• 3883 Chip crusher error
• 3884 Workpiece puller operation incomplete
• 3885 No workpiece
• 3886 Workpiece present
• 3887 Temperature control unit error
• 3888 Chip conveyor faulty
• 3889 EExternal start signal ON
• 3890 Low level in oil tank
• 3891 Multi-counter tool life
• 3892 Hydraulic oil level lower limit
• 3893 Hydraulic unit oil controller
• 3894 Spindle lubrication controller error
• 3895 Coolant controller error
• 3896 Tool change count-up
• 3897 Workpiece stocker full
• 3898 Cooler error
• 3900 User reserve code
• 3901 External

5. Bảng mã lỗi máy CNC Okuma – Alarm D List

• 4035 Replace memory board battery
• 4036 Key-code data receipt error
• 4037 CCP-CPU error
• 4052 PLC backup data file write
• 4054 ACP key-code data receipt error
• 4055 Safety speed clamping
• 4056 Adjusting Type-J encoder
• 4057 Battery life
• 4058 Previous backup error
• 4059 Backup file error
• 4060 AlarmService internal error
• 4061 UPS Service error
• 4062 Remote Diagnosis error
• 4063 DNC2 communication error
• 4064 Awaiting establishment of DeviceNet
• 4065 FL-net transmission error
• 4066 FL-net transmission failure
• 4067 Maintenance necessary
• 4068 Non-responsive software detected
• 4069 Turret index sequence has not ended.
• 4070 Solid model position error
• 4071 CAS environment file cannot be changed
• 4072 Turret position error
• 4076 CAS software calculation error
• 4077 Turning interlock of CAS
• 4078 Error occurred during CAS
• 4080 Collision Avoidance Function OFF
• 4081 In-position/droop check waiting status
• 4083 Windows updated. Reboot
• 4084 Virus has been detected.
• 4085 Fan motor error at panel computer unit
• 4086 UPS not functioning
• 4087 Non-functioning device detected
• 4088 Virus Detect Function active
• 4090 Machine relocation detected
• 4091 Var. lost motion cannot be applied.
• 4092 MCS Parameter learning
• 4100 Collision avoidance position
• 4101 CAS software environment being changed
• 4102 Awaiting CAS software process
• 4103 Drawing speed over
• 4104 CAS processing time over
• 4105 Collision block detected
• 4106 Collision Avoidance system OFF
• 4107 Awaiting CAS check result
• 4108 Inaccurate material shape
• 4109 CAS operating in rapid mode
• 4110 Turret collision check not performed
• 4120 Overload detected
• 4121 General overload detection disabled
• 4122 Maintenance (by user) necessary
• 4130 MCS Inertia identification
• 4131 VDU initialization failure
• 4132 VDU communication error
• 4133 VDU error
• 4134 MCS Alarm-D occurred
• 4135 MCS DD encoder link error
• 4136 MCS DD encoder error
• 4137 MCS DD encoder (slave sensor) detected error
• 4138 MCS DD encoder initialization failure
• 4139 MCS DD encoder (slave sensor) initialization failure
• 4141 MCS Push reset button to stop spindle
• 4144 MCS power supply unit overload
• 4145 MCS Drive unit external cooling fan stop
• 4147 MCS Drive unit internal cooling fan stop
• 4148 MCS Power supply unit external cooling fan stop
• 4149 MCS Power supply unit internal cooling fan stop
• 4150 MCS Undefined alarm number
• 4151 MCS Inverter unit fault
• 4152 Mistake in data from MCS to NC
• 4153 MCS CON APA deviation
• 4154 MCS Power supply unit error
• 4155 MCS Converter link error
• 4156 MCS DC-bus voltage alarm
• 4157 MCS Motor overcurrent
• 4158 MCS Power unit overheat
• 4159 MCS Power unit overload
• 4160 MCS Supply voltage flutter
• 4161 MCS Inverter capacity differs from spec.
• 4162 MCS Winding change failure
• 4163 MCS Encoder link error
• 4164 MCS Encoder detected error
• 4165 MCS Encoder initialization failure
• 4166 MCS Encoder with shaft detected error
• 4167 MCS Encoder with shaft initialization failure
• 4168 MCS ABSO SCALE error
• 4169 MCS ABSO SCALE initialization failure
• 4170 MCS Magnetic encoder alarm
• 4171 MCS Resolver alarm
• 4172 MCS Pulse generator count over
• 4173 MCS Motor overheat
• 4174 MCS Servo link error
• 4175 MCS Servo link disconnection
• 4176 Mistake in data from NC to MCS
• 4177 MCS Servo data error
• 4178 MCS Illegal command
• 4179 MCS CON speed over
• 4180 MCS Speed command over
• 4181 MCS DIFF over
• 4182 MCS APA speed over
• 4183 MCS Full-closed APA error
• 4184 MCS Over speed
• 4185 MCS Speed deviation over
• 4186 MCS Collision detected
• 4187 MCS Urgent-stop time over
• 4188 MCS Belt is broken
• 4190 MCS Independent encoder initialization failure
• 4191 MCS Calculated current position lies outside range
• 4192 MCS Motor overload
• 4194 MCS ABSO SCALE sub-slider detected error
• 4195 MCS Tandem control communication error
• 4196 MCS Full abso scale link error
• 4197 MCS Full abso scale error
• 4198 MCS Full abso scale initialization failure
• 4199 MCS Axis stop signal error
• 4200 Reboot enabled parameter set
• 4201 MACHINING MANAGEMENT data backup stop
• 4202 DNC-B Communication system abort
• 4203 DNC-B Communication error
• 4204 DNC-B Message format error
• 4205 H1 turret interference barrier parameter not set
• 4206 SPM Parameter unsuitable
• 4207 Unable to execute Hi-CUT Pro control
• 4208 G265/G264 commands: Unusable address character
• 4209 Hi-CUT Pro parameter out of range (replacing)
• 4210 SPM contour control not possible
• 4211 SPM parameter out of range (replacing)
• 4214 RS232C communication not ready
• 4215 Communication buffer over
• 4216 Communication procedure No response
• 4217 Communication procedure NAK/WACK
• 4218 Communication procedure Illegal text
• 4219 Communication procedure ENQ
• 4220 Communication procedure EOT
• 4221 Communication procedure TTD
• 4223 Motor not ready to start
• 4224 Canceling stroke end limit
• 4225 Pitch compensation data calculation
• 4226 MSB load error
• 4227 External start not possible
• 4228 SSynchronized rotation speed over
• 4230 Torque limit recovery
• 4232 Backup data read/write
• 4237 Magazine operation panel communication error
• 4238 Please open magazine door
• 4240 Tool life management No spare tool
• 4242 Parameter set value incorrect
• 4245 Waiting program selection during program operation.
• 4247 Main spindle max. speed designation
• 4248 DNC NC receipt start conditions
• 4249 Tool life warning
• 4251 Axis feed rate restriction
• 4252 Detector operation check mode
• 4258 Y-axis cancel mode
• 4261 Workpiece counter over
• 4267 PLC link error
• 4268 PLC communication error
• 4269 ROBOT control
• 4274 User reserve code
• 4281 Workpiece counter over
• 4284 Thermistor error
• 4285 Thermal deviation compensation
• 4288 PSC Learn converge protect error
• 4289 Spindle able to enter transportation barrier
• 4290 TCP/IP communication error
• 4291 Position encoder auto adjustment
• 4292 Please check the program
• 4294 Extended Y-axis plus variable limit
• 4295 TDC parameter not set
• 4297 Main Magazine tool Quantity over
• 4298 DNC Ethernet communication error
• 4300 B-axis independent encoder connecting
• 4301 Tail-stock position error
• 4302 Please supply oil of chuck
• 4303 Movement to sizing position stopped
• 4304 No axis movement after offset change
• 4305 Y-axis not at turning position
• 4306 Turret movement decelerating
• 4307 Alarm-A at other system
• 4308 X-axis over limit
• 4309 Clutch A slip monitor OFF
• 4311 Interrupt program
• 4314 Learning required for cam data
• 4315 Permissible value exceeded
• 4316 Manual feed invalid
• 4345 Unable to execute feed axis retract function
• 4346 ZA-W interference parameter not set
• 4347 TDC invalid
• 4348 X-C-axis coordinate value error
• 4349 Mode switching impossible
• 4682 Magnetic encoder speed detection error
• 4683 MCS Rotary encoder 5 initialization failure
• 4684 MCS Rotary encoder 5 error
• 4685 MCS Rotary encoder 4 initialization failure
• 4686 MCS Rotary encoder 4 error
• 4687 MCS Rotary encoder 3 initialization failure
• 4688 MCS Rotary encoder 3 error
• 4689 MCS Rotary encoder 2 error
• 4690 MCS Rotary encoder 1 initialization failure
• 4691 MCS Rotary encoder 1 error
• 4692 MCS Linear scale 4 initialization failure
• 4693 MCS Linear scale 4 error
• 4694 MCS Linear scale 3 initialization failure
• 4695 MCS Linear scale 3 error
• 4696 MCS Linear scale 2 initialization failure
• 4697 MCS Linear scale 2 error
• 4698 MCS Linear scale 1 initialization failure
• 4699 MCS Linear scale 1 error
• 4700 External cycle start interlock
• 4701 Chip conveyer overload
• 4702 Cycle start interlock
• 4703 Canceling stroke end limit
• 4704 Please open door
• 4705 Door interlock all axis stop
• 4706 Canceling door interlock
• 4707 Enabling Switch faulty
• 4708 ATC system mode
• 4709 Power sequence error
• 4710 Parameter non set
• 4711 Spindle motor not ready to start
• 4712 Reboot enabled parameter set
• 4713 Executing power OFF sequence
• 4714 Workpiece counter full count
• 4715 Preparing for warming up
• 4716 Motor not ready to start
• 4717 Dual cycle start button interlock
• 4718 Invalid parameter setting
• 4719 Please open side cover
• 4720 Dual cycle start button interlock
• 4721 Feed rate limitation
• 4722 System check mode
• 4723 Machine enabling button pressed
• 4724 Please open safety fence
• 4725 Please close front door
• 4726 Opposite side front door open
• 4727 Safety fence open
• 4728 Please close other side front door
• 4729 Please open magazin door
• 4730 Magazine door open
• 4731 Multiple safety guards open
• 4732 Gauging sensor power ON
• 4733 Measurement system error
• 4734 Please close safety guards
• 4735 Full of chips
• 4736 Sensor head
• 4737 Other door open
• 4738 Magazine OP panel COMM error
• 4739 Turret not ready to start
• 4740 2nd Spindle control interlock
• 4741 Magazine operation panel manual interrupt
• 4742 Turret encoder offset disabled area
• 4743 Turret index disabled area
• 4744 Turnover cycle
• 4745 REDUCE switch operation error
• 4746 Tool change mode sw operation error
• 4747 Gauging sensor battery change
• 4748 Additional coolant level low
• 4749 Please close door
• 4750 Safety interlock
• 4751 Tailstock quill interlock
• 4752 Tailstock absolute coder error
• 4753 Workpiece hand control
• 4754 Bar stock empty
• 4755 Roof window open interlock
• 4756 Canceling robot/loader and machine interlock
• 4757 Sp. oil air lub. air extraction mode
• 4758 Index chuck adjust mode
• 4760 Moving to home position
• 4761 Override condition
• 4762 Side cover open
• 4763 Home position return interlock
• 4764 Spindle orientation interlock
• 4765 Setup not complete
• 4766 Setup complete interlock
• 4767 ACC safety door locking switch NG
• 4768 Please open ACC safety door
• 4769 ACC system mode
• 4770 Mode switch NG
• 4771 Magnet chuck unclamp cycle
• 4772 Tool select switch mismatch
• 4773 ATC shutter barrier area
• 4774 Invalid zero offset no.
• 4775 Please open spindle cover
• 4776 Canceling interference detection
• 4777 Mist collector power OFF
• 4778 Side cover open
• 4779 ATC shutter interlock cancel mode
• 4780 Maintenance door open
• 4781 Ladder gate open.
• 4782 Workpiece stocker error
• 4783 Workpiece stocker overload
• 4784 Mist collector error
• 4785 Self check counter full count
• 4786 Coolant controller error
• 4787 Manual tool change enabled
• 4788 Chip conveyer stop
• 4789 Sensor overstroke
• 4790 Chucking miss air route clogged
• 4791 Linear guide cover interference
• 4792 Workpiece washer overload
• 4793 Coolant filter
• 4794 Sequencer alarm
• 4795 Please open ceiling door
• 4796 APC safety interlock
• 4797 Please open APC door
• 4798 APC door lock incomplete
• 4800 Tow-along steady rest connection
• 4801 Oil mist error
• 4802 Turret rotation interlock
• 4803 Cross rail positioning auto set mode
• 4804 Workpiece washing gun error
• 4805 Coolant unit error
• 4806 Lube oil drain tank overflow
• 4807 Axis lube level low
• 4808 Coolant level low
• 4809 ATC step time over
• 4810 System check
• 4811 Coolant tank upper level
• 4812 Chip crusher error
• 4813 Waiting for workpiece check
• 4814 Chuck open/close interlock
• 4815 Attachment turret rotating
• 4816 Long boring bar interlock
• 4817 Safety door open interlock
• 4818 Attachment manual change mode
• 4819 ATC door not at end of stroke
• 4820 M-Spindle rotation limit
• 4821 Steady rest interlock
• 4822 Feed axis condition
• 4823 Turret indexing at reduced speed
• 4824 Setup mode
• 4825 Axis position encoder control error
• 4826 General overload detection disabled
• 4827 Canceling chuck grasp interlockl
• 4828 Please switch door interlock ON
• 4829 NC tailstock thrust change interlock
• 4830 Tool indexing not complete
• 4831 Door interlock
• 4844 Coupling device interlock
• 4845 Coolant level warning
• 4846 Unloader setting position parameter
• 4847 Interference area intrusion
• 4848 No lower table present signal
• 4849 Coolant level
• 4850 Safety fence interlock
• 4851 Door interlock
• 4852 Canceling stroke end limit
• 4853 Robot/loader power sequence error
• 4854 Loader interference
• 4855 Front door open interlock
• 4856 Please open safety fence
• 4857 Please close safety fence
• 4858 Feed rate limit
• 4859 Teaching panel enabling switch error
• 4860 Multiple safety guards open
• 4861 Equip. safety fence parameter mismatch
• 4862 Dual cycle start button interlock
• 4863 Tool change count-up
• 4864 Other door open
• 4865 Performing turnover cycle
• 4866 No workpiece
• 4867 M-spindle angle uncertain
• 4868 Cycle start interlock
• 4869 Chuck was changed
• 4870 Invalid servo data selection
• 4871 Inside barrier
• 4872 Tailstock fretting
• 4873 Door open/close limit switch NG
• 4874 XB cover interference
• 4875 Please push the NC start button
• 4876 Please discharge coolant
• 4877 Invalid positioning point
• 4878 Pulse handle mode
• 4879 Curvic cover not attached
• 4880 Measurement unit error
• 4881 NG chute workpiece present
• 4882 Quality check counter notice count
• 4883 Tow-along tailstock unclamp
• 4884 Tool counter full count
• 4885 Quality check counter full count
• 4886 Tool counter warning
• 4887 Tailstock/Chuck Pedal Enable
• 4888 Mode switch operation error
• 4889 PLC link error
• 4890 Dust collector in local mode
• 4891 Chip conveyor in local mode
• 4892 Chip conveyor error
• 4893 OP panel not at retract position
• 4894 Multi-counter tool life warning
• 4895 Hydraulic fluid level low
• 4896 Lubricant level
• 4897 Gauging data ready time out
• 4898 Power save ON
• 4899 Lower turret origin return interlock
• 4900 Motor not ready to start
• 4903 Reboot enabled parameter set
• 4904 Barrier intrusion
• 4905 Safety speed clamping
• 4907 Alarm-A at other system

Bảng mã lỗi máy CNC Okuma – VNC Automation Cung cấp dịch vụ Sửa chữa lỗi, thay thế, nâng cấp hệ điều khiển máy CNC Okuma và các hãng khác